|
Aqua Lung® Dry Cap
Socket
The Dry Cap Socket is
designed to accurately
apply torque to the
ambient diaphragm cap on
the dry versions of the
Titan and Cousteau first
stages.
The socket incorporates
a drive blade that
indexes with the slots
in the cap. A centering
flange maintains
alignment during
torquing operations. A
3/8" drive torque wrench
can be fitted directly
to the socket (see
second illustration
above).
|
|
Dry Cap Socket |
| SI-20226100
$32.00 |
|
|
|
| |
|
|
"C" Clip Tool
The "C"
Clip Tool is designed to
assist in the
disassembly/assembly of
the following second
stages:
SeaQuest® XR2® (all tool
functions)
Aqua Lung® Impulse® (all
tool functions)
Aqua Lung Micra®-Micra
ADJ®
("C" Clip function)
Genesis® Valor® ("C"
Clip function)
The illustrations show
the basic function of
the tool. For additional
information regarding
the repair procedures
for these second stages,
consult the specific
manufacturers' repair
manuals.
Figure #1: The SeaQuest
XR2 and the Aqua Lung
Impulse utilize an
internal threaded ring
that retains the
diaphragm and
frictionless washer. The
two side pins on the
tool will index with any
two cross holes or slots
in the ring and allow it
to be rotated in either
direction.
Figure #2: The flow vane
assembly on all of the
above second stages is
retained by an internal
"C" clip. The forked end
of the tool is designed
to push on both ends of
the clip simultaneously.
The clip can be removed
from either the
diaphragm or the
mouthpiece side of the
housing. If the clip is
removed via the
mouthpiece channel, the
tool can be rested flat
against the housing.
This method eliminates
the possibility of the
tool digging into the
housing. The only
disadvantage to removing
the clip from this side,
is that the open end of
the clip must be turned
so that it faces in the
opposite direction.
Figure #3: The "C" clip
can only be installed
from the mouthpiece side
of the second stage. The
forked end of the tool
has a machined ledge to
hold the "C" clip. Press
the clip into the ledge
by applying pressure
that will slightly
spread the forks. This
spring tension will
retain the clip while it
is being positioned.
Push the clip onto the
molded groove on the
flow vane body. Be sure
that the clip is fully
installed and locked in
place. The watertight
integrity of the housing
relies on this assembly. |
|
"C" Clip Tool |
| SI-20187200
$21.00 |
|
|
|
| |
|
Quad Spanner Wrench
The Quad Spanner Wrench
is specifically designed
to aid in the
disassembly/assembly of
the Pioneer®, Nordic®,
Century®, Infinity®,
Mirage®, and Aquarius®
first stages. The tool
includes 4 different
spanner wrenches that
fit the pin holes in the
various components of
these regulators. The
illustrations show the
appropriate use of each
spanner and the
relationship of the
parts as they are
disassembled. These
drawings are
self-explanatory for all
spanner applications.
All Quad Spanner pins
are replaceable should
they become damaged. A
complete replacement set
of pins is included for
your convenience. The
worn or damaged pins can
be removed with a
standard 1/8" punch. It
is important to remove
the damaged portion of
the pin with a file or
bench grinder before
attempting to drive the
pin out of the wrench.
This will prevent
enlarging the pin hole
and maintain a secure
fit for the replacement
pin. The Quad Spanner
Wrench is machined from
aluminum and anodized
blue. |
|
Quad Spanner Wrench |
|
SI-20180200
$35.00 |
|
|
|
| |
|
|
Micra Cover Ring Split Clamp
The Micra Cover Ring
Split Clamp is the
newest in a series of
similar clamps used to
remove outer cover rings
that can not be removed
easily by hand. This
clamp fits both the
plastic and metal rings
used on the Micra family
of second stages. The
split clamp design
provides nearly 100%
contact with the outer
diameter of the ring.
The best method for
using the split clamp is
to capture the clamp in
a bench vise. Clamping
force should be applied
gently until the split
in the clamp closes on
the ring. With the
second stage secured in
this manner, the second
stage housing can be
turned to loosen the
ring. |
|
Micra Cover Ring Split Clamp |
| SI-20206200
$23.00 |
|
|
|
| |
|
Cover Retaining Ring
Tool
The Cover Retaining Ring
Tool is designed to
thread/unthread the
notched retaining ring
that secures the logo
cover and diaphragm in
the Aqua Lung® Micra (Micra
ADJ) and Genesis® Valor
second stages.
The machined drive tabs
on the tool index with
any two adjacent notches
in the retaining ring,
permitting the ring to
be easily
removed/installed. The
inside diameter of the
tool has been reduced to
allow it to slide over
the logo cover. The
orientation of the logo,
in relationship to the
second stage housing,
may require some trial
and error to achieve
precise alignment.
The Cover Retaining Ring
Tool is machined from
6061-T6 aluminum tubing.
|
|
Cover Retaining Ring Tool
|
| SI-20210200
$15.00 |
|
|
|
| |
|
Micra
ADJ Knob Tool Kit
The Micra ADJ Knob Tool
Kit consists of three
individual tools
(pictured above). When
used in the proper
sequence, they will
allow easy
removal/installation of
the 1/16" SS tension pin
used to retain the knob
on the Aqua Lung Micra
ADJ (see Figures #1, #2,
& #3).
The punch is made from
hardened high speed
steel and can be used
from either end. When
tapping on this punch
with a hammer, be sure
to hit the punch
squarely and not at an
angle. Always wear eye
protection when using
hardened punches!
The alignment block is
precision machined from
solid brass. When the
block is clamped in a
standard bench vise, it
forms a "hands free"
fixture that positions
the knob so that the
tension pin can be
easily
removed/installed.
The
alignment probe is a
stainless steel teasing
needle that is used to
align the hole in the
knob with the hole in
the air barrel. When
positioned in the
alignment block, the
tension pin can be
tapped into place to
secure the knob.
Complete instructions
for the use of this tool
kit are included with
the kit. |
|
Micra ADJ Knob Tool Kit
|
| SI-20205100
$25.00 |
|
|
|
| |
|
Aqua
Lung Lever Height
Adjustment
Tool Kit
The Aqua Lung Lever
Height Adjusting Tool
Kit fits 21 earlier
models of Aqua Lung®
second stages. It
replaces the original
Aqua Lung tool assembly
that incorporated a
hollow shafted 1/4" nut
driver and reground
screwdriver.
This tool features a
custom 1/4" socket
driver that is
specifically engineered
to fit the second stage
housing port. It has an
internal guide that
precisely centers the
screwdriver bit with the
slot in the poppet
shaft. The socket driver
is machined from
stainless steel.
The screwdriver is a
2.5mm Wiha precision
slotted driver. The tip
is precision ground for
exact fit. The bade is
manufactured from chrome
vanadium molybdenum
steel, hardened, and
vapor chrome plated. The
cadmium free handle has
a swivel cap for maximum
feel and control.
Together, these two
tools form the ideal
combination for making
final adjustments to the
demand valve and lever
height. The overall
assembly is shorter and
easier to handle than
the original tool, and
the screwdriver bit
indexes with the poppet
slot every time. |
|
Lever Height Adjustment Tool |
| SI-20215500
$34.00 |
|
|
|
| |
|
|
Aqua Lung Poppet Driver
The Aqua Lung Poppet
Driver is designed to
assist the technician in
the assembly of valve
components in 30 older
Aqua Lung® second
stages.
The tool incorporates a
sliding nut that can be
threaded into the valve
body from outside the
second stage housing.
The nut holds the poppet
and spring in place
while the washers and
nut are installed
internally. This feature
eliminates the need to
compress and hold the
poppet spring tension
during this operation.
The poppet stem is
machined with four drive
slots that index with
the poppet tabs. The
stem and poppet can be
freely rotated by
turning the external
knob. This tool feature
allows the nut to be
held stationary while
the poppet is turned to
start the nut and thread
it onto the poppet shaft
The Aqua Lung Poppet
Driver shaft and sliding
nut are machined from
300 series stainless
steel.
The Aqua Lung Poppet
Driver is shipped with
complete instructions
for tool use.
|
|
Aqua Lung Poppet Driver |
| SI-20220100
$30.00 |
|
|
|
